You are viewing the article How to program a Chamberlain Clicker Universal Remote Control / LiftMaster 375? at Tnhelearning.edu.vn you can quickly access the necessary information in the table of contents of the article below.
The Chamberlain Clicker Universal Remote Control (KLIK1U, KLIK3U, KLIK3U-BL, KLIK3U-PK)
aka LiftMaster 375UT (375 LM) is a universal remote that
will program to most garage door openers and external receivers using learn buttons or DIP switches.
The first step is determining if your garage door opener or external receiver uses a learn button or DIP
switches.
and older units utilize DIP switches.
Programming the clicker universal remote to a garage door opener/receiver with learn button:
1. Start with the garage door closed.
2. Open the remote by sliding the battery cover open. Inside the remote you will see a
program button on one side and DIP switches on the other side. Press and hold the program
3. Press the learn button on the garage door opener or external receiver. The learn button will be
on the back or side of the garage door opener motor. You will have to use a ladder to locate and
access the learn button. Always use caution any time you use a ladder to prevent accidental
falls.
4. Press and release the button on the remote you want to operate the garage door opener. Wait
until the LED on the remote stops flashing between button pushes. Continue to press the
button until you hear a click from the garage door opener, the light on the garage door opener
flashes or the garage door starts to open.
5. Press and release the program button to exit the programming mode.
6. Press the button you just programmed to verify the garage door opener remote is programmed
and the garage door opens and closes using the remote. If the garage door does not open and
close, repeat the programming steps.
These same steps work for programming to an external receiver or a gate opener with a learn button.
Number of button pushes required for the following Openers to program the universal clicker:
(Number of times press and release require / Learn button and Years
Brand / Models)
|
|
|
|
|
|
|
|
|
|
|
|
|
Master Mechanic 642-2MM
|
|
|
|
|
|
|
|
|
|
Access Master M385,
|
|
|
|
|
ChainMax 1000, ChainMax 1200, ChainMax 1200 4042, SilentMax 750, SilentMax 1000, SILENTMAX 1000 3042, SILENTMAX 1200, SILENTMAX 1200 4042, TriloG 1200, TriloG 1500, TriloG 1500 4064, TriloG 1500 4064H, PowerLift 900, PowerMax 1200, PowerMax 1500, IntelliG 1000, IntelliG 1000 3024, IntelliG 1000 3024H, IntelliG 1200, IntelliG 1200 4024, IntelliG 1200 4024H, CB 1000, CB 1200, 1022, 1024, 1028, 1028B, 1035, 1042, 1128, 1128B, 2020, 2022, 2024, 2028, 2028B, 2035, 2036, 2040, 2040L, 2042, 2055, 2128B, 2128, 3024H, 3024H-B, 3035, 3055, 3064, 3120HL, 3120HL-B, 3120H, 3120H-B 4064H, 4064H-B, 4124H, 4124H-B, 4164H, 4164H-B, 6070H, 6070H-B, 6170H, 6170H-B, 7035, 7055, BeltLift 600, Directlift 2060, Directlift 3060, GPower 900, Machforce 4062, Excelerator 4062, SilentMax Connect, SteakthDrive 750, StealthDrive 750 Plus,
|
|
H8000, 4560, 500ML, 700ML, Excelerator, GCG350,
350L, 350L-1x, 350L-2, 350L-2C, 350L-2WK, 350L-2WKC, Chain Glide, H2000,
OverHead Legacy
|
|
|
|
|
|
|
|
|
|
|
|
Merlin – MJ3800MYQ, MS125MYQ, MS105MYQ, MR855MYQ, MS65MYQ, MR655MYQ, MT3850EVO, MR555MYQ, MT110MYQ, MT120EVOPS, MT60EVO, MT100EVO,
Do-It, Master Mechanic, True Value
Access Mater – M885, M8856
Craftsman -CMXEOCG471,CMXEOCG981, CMXEOCG231,CMXEOCG571, CMXEOCG771, CMXEOCG781
|
|
3014, 3018, 3018DLX, 3514, 3314, 3414, 3220C, 3222C, 3224C, 3320B, 3322B, 3322B, 3324B, 3212, 3213, 3312, 3313, 3412, 3012, 3016, 3512
|
|
|
|
|
|
Remember the LED light on the clicker must stop flashing between each press of the button during
programming.
If your garage door opener or receiver utilizes DIP switches you must match the DIP switches on the
remote to the DIP switches on the garage door opener or receiver. It could be 8-12 DIP switches with 2
or 3 positions per switch. The DIP switches much match identically. If your garage door opener or
receiver has only 2 positions and programming does not work, switch the off and on positions on the
remote as they may be reversed.
Program chamberlain garage door opener and clickers, in general, is a fairly simple process if you follow the listed procedures. You can
contact a local garage door service company to provide the remote and program the remote for you.
Labor rates will vary depending on your area but is normally around $70 – $120 (Include full garage door
and opener inspection) and the cost of the universal clicker remote is around $35 – $50.
Thank you for reading this post How to program a Chamberlain Clicker Universal Remote Control / LiftMaster 375? at Tnhelearning.edu.vn You can comment, see more related articles below and hope to help you with interesting information.
Related Search: