You are viewing the article How to Connect the Coaxial Cable Terminal at Tnhelearning.edu.vn you can quickly access the necessary information in the table of contents of the article below.
This article is co-authored by a team of editors and trained researchers who confirm the accuracy and completeness of the article.
The wikiHow Content Management team carefully monitors the work of editors to ensure that every article is up to a high standard of quality.
There are 9 references cited in this article that you can view at the bottom of the page.
This article has been viewed 3,339 times.
Coax cable is used to transmit Internet and TV signals to homes and other buildings. These cables need connectors to plug into electrical devices (such as TVs) and transmit signals. If the coax cable doesn’t have a connector, you can easily install it yourself. Just peel off the cover to reveal the wires inside, attach the connector and press cos to secure. If using in a tight space, it is recommended to use a right-angle connector to avoid bending the cable too much.
Steps
Select and strip the cable
- The difference between these two cables is that the RG6 is larger and has a thicker shielding than the RG59. This makes RG6 more stable and widely used for cable television and Internet.
- There is also a type N connector, but this type is rarely used in home installations.
- F-connectors are also available in a variety of designs, which include push-in (by pressing cos) and screw-in. Talk to the seller if you don’t know which one to buy.
- Only cut the outer rubber cover, do not cut the entire cable. Cutting too deep can damage the conductor.
- If you use a shaver, be careful. Do not put your finger in the cut of the blade, while holding the cable firmly.
- The wire stripper can cut the entire mesh layer, so you need to be careful to use moderate force. If you cut too deep, you can damage the copper core in the middle of the cable.
- The plastic case can be covered by a thin film coated with aluminum.
- Be especially careful when peeling off this plastic cover. If you affect the copper core, the transmission signal will be poor.
Attach a pressurized connector
- Not all connectors use a removable connector. Some connectors are attached to the connector jack. You need to determine whether this connector uses a separate or connected jack.
- You will need to use force to push the connector between the rubber cover and the white plastic. Try twisting the connector back and forth while attaching the cable.
- If you are installing the cable outdoors, don’t forget to use a waterproof connector. Connectors of this type usually have a rubber coating on the outside.
- Some cos presses work in a different way. Follow the instructions depending on the tools you have.
Connect the connector perpendicularly
- Don’t forget to attach this base before attaching other parts of the connector. Otherwise, you will have to remove the connector to reattach the base.
- Some sets of perpendicular connectors have a different configuration. But in general, you should still follow this procedure with any perpendicular connector.
- It is not necessary to completely remove the screw. You only need to loosen enough to attach the conductor.
- Only tighten until the screw fits snugly and holds the copper core. Do not over tighten as you may damage the wire.
- Some connectors will match and make a “click” sound when you push them in. Continue to hold the two parts of the connector in case they do not automatically match.
Advice
- If you use a high-speed Internet connection and more than two TVs, choose a good RG 6 connector.
- Screw type F connectors often result in poor connections and possible signal loss. Pressed connector for better signal.
Things you need
- Coaxial Cable
- Coaxial cable connector
- Wire cutting pliers
- Cable stripping pliers
- Pliers
- Razor
- pliers cos
- Wire stripping pliers
This article is co-authored by a team of editors and trained researchers who confirm the accuracy and completeness of the article.
The wikiHow Content Management team carefully monitors the work of editors to ensure that every article is up to a high standard of quality.
There are 9 references cited in this article that you can view at the bottom of the page.
This article has been viewed 3,339 times.
Coax cable is used to transmit Internet and TV signals to homes and other buildings. These cables need connectors to plug into electrical devices (such as TVs) and transmit signals. If the coax cable doesn’t have a connector, you can easily install it yourself. Just peel off the cover to reveal the wires inside, attach the connector and press cos to secure. If using in a tight space, it is recommended to use a right-angle connector to avoid bending the cable too much.
Thank you for reading this post How to Connect the Coaxial Cable Terminal at Tnhelearning.edu.vn You can comment, see more related articles below and hope to help you with interesting information.
Related Search: