You are viewing the article How to disable the car seat belt warning bell at Tnhelearning.edu.vn you can quickly access the necessary information in the table of contents of the article below.
This article is co-authored by a team of editors and trained researchers who confirm the accuracy and completeness of the article.
The wikiHow Content Management team carefully monitors the work of editors to ensure that every article is up to a high standard of quality.
This article has been viewed 12,388 times.
Everyone knows that wearing a seat belt while driving is essential. However, there are many situations that make seat belt warnings a nuisance. For example, when driving in the countryside at a slow speed and needing to stop several times, you may not want to wear your seat belt. Or when traveling in an urban area and you want to let your dog sit in the front passenger seat, the constant “ding ding” sound will be annoying. Sometimes the alarm goes “stuck” and makes a headache, whether you’re wearing a seat belt or not. Fortunately, you can disable the seat belt warning in several ways.
Steps
Use the manufacturer’s tools
- Plug in the key and turn on the electrical system. Do not start the car.
- On the control panel there is a button used to turn on / off the distance measurement or the total distance traveled. Press this button until “ODO” appears on the control panel.
- Turn off the key and open it again. [2] X Research Source
- Press and hold the button just now for about 10-15 seconds, at the same time, fasten your seat belt and release your hand from the button.
- The message “B OFF” will flash on the control panel indicating that the seat belt warning has been deactivated.
- You should be aware that agents are often reluctant to make this request because of liability issues. However, it is the safest way to disable the seat belt warning bell, so the dealer can sometimes be flexible about special circumstances. [4] X Research Sources
Install seat belt warning muffler
- Compare the overall dimensions of the metal contact on the blade with the buckle before purchasing.
- Don’t forget that driving without a seat belt is very dangerous and also violates traffic laws in most countries.
- Compliance with the extender standard is important, as the system needs to pass seat belt testing to ensure impact resistance. You can consult these requirements online or ask the seat belt manufacturer.
Advice
- You may need a flash to get a better look under the seat.
- After disabling the seat belt warning bell, test drive the vehicle to check its effectiveness; If you accidentally cut the power cord, you can use the electrical connector to reconnect it.
- During disabling the alarm, it makes no difference if the belt is being fastened or not. However, this depends on the model of the vehicle.
Warning
- Tampering with the seat belt may affect the vehicle warranty.
- The locking belt should not be cut as this may affect the operation of the front-seat airbags. On some cars, cutting the buckle belt has the opposite effect, causing the warning bell to ring continuously.
- We recommend that you do not attempt to disable the alarm by tapping the lock. Some seat belts contain airbag detonators that can be accidentally activated if you crank the engine. In addition, removing or tampering with parts inside the buckle can cause the seat belt to fall out in an accident.
- Tampering with the seat belt sensor can sometimes affect the operation of the airbag. This could put you or the people in the vehicle at risk. Check that the airbag is not affected before adjusting the seat belt warning bell sensor.
Things you need
Install seat belt warning muffler
- Seat belt alarm muffler or extender
Use the manufacturer’s tools
- User Manual
- Software update (if possible or necessary)
This article is co-authored by a team of editors and trained researchers who confirm the accuracy and completeness of the article.
The wikiHow Content Management team carefully monitors the work of editors to ensure that every article is up to a high standard of quality.
This article has been viewed 12,388 times.
Everyone knows that wearing a seat belt while driving is essential. However, there are many situations that make seat belt warnings a nuisance. For example, when driving in the countryside at a slow speed and needing to stop several times, you may not want to wear your seat belt. Or when traveling in an urban area and you want to let your dog sit in the front passenger seat, the constant “ding ding” sound will be annoying. Sometimes the alarm goes “stuck” and makes a headache, whether you’re wearing a seat belt or not. Fortunately, you can disable the seat belt warning in several ways.
Thank you for reading this post How to disable the car seat belt warning bell at Tnhelearning.edu.vn You can comment, see more related articles below and hope to help you with interesting information.
Related Search: