How to Hang things on a cement wall

Decorating a cement wall is a complicated job if you don’t have the right tools. Fortunately, there are a few great ways to do it without resorting to expensive and hard-to-find tools. Choose a 8 pound (3.6 kg) wall hook for hanging light items, a 25 lb (11 kg) pushpin wall hook, and an expansion screw for hanging decorations that weigh over 25 pounds pounds (11 kg).

Table of Contents

Attach wall hooks

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/0/04/Hang-Things-on-a-Cement-Wall-Step-1.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-1.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/0/04/Hang-Things-on-a-Cement-Wall- Step-1.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-1.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Choose wall hooks to hang objects weighing up to 8 pounds (3.6 kg). Because the back of the hook has super glue, you don’t need to punch holes in the wall. First, weigh the object to choose the right hook. ^{[1] X Research Source}

Wall hook products are diverse in size and specify the maximum weight that can be held. The largest wall hook can hold up to 8 pounds (3.6 kg), while the smallest can only withstand 1 pound (0.45 kg) hanging force.
Use 2 hooks at the same time if the item has a cord or has a built-in hook on the back.

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/f/fe/Hang-Things-on-a-Cement-Wall-Step-2.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-2.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/f/fe/Hang-Things-on-a-Cement-Wall- Step-2.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-2.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Clean the wall with alcohol to make the hook stick better. Dip a clean rag or paper towel in the rubbing alcohol solution and then wipe off any dirt, old grout remaining on the wall. This helps the hook stick to the wall. ^{[2] X Research Source}

If you don’t have rubbing alcohol, try cleaning the wall with warm soapy water. Dry the area that has just been cleaned.

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/e/e0/Hang-Things-on-a-Cement-Wall-Step-3.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-3.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/e/e0/Hang-Things-on-a-Cement-Wall- Step-3.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-3.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Use a pencil to mark the point where you want to stick the hook. If the item has a wire in the back, note the length of the slack. Test by stretching the midpoint of the rope towards the top of the object. Measure the distance from the bottom of the item to where the center point of the wire reaches when fully stretched.

If you are going to hang an item that has two hooks attached on the back to the 2 wall hooks, be sure to measure the distance between the two hooks to mark on the wall.
If you are hanging an object with a wire attached to 2 wall hooks, measure the width of the object and divide it by 3. You should leave the two wall hooks a distance apart from the result of the division just now.

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/5/5b/Hang-Things-on-a-Cement-Wall-Step-4.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-4.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/5/5b/Hang-Things-on-a-Cement-Wall- Step-4.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-4.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Separate the double-sided tape from the tape protection and attach it to the back of the hook. If there is no adhesive on the back of the wall hook, peel off the protective piece from one side of the tape. Stick that side of the tape to the back of the wall hook and tighten it with your hands.

Some types of wall hooks have glue on the back. If you own such a hook, skip this step and move on to the next step.

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/5/5a/Hang-Things-on-a-Cement-Wall-Step-5.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-5.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/5/5a/Hang-Things-on-a-Cement-Wall- Step-5.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-5.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Press firmly for about 30 seconds for the hook to stick firmly to the wall. Peel off the protective paper on the back of the hook, pull it out slowly vertically, and firmly press the hook to the wall. Hold for about 30 seconds and then release.

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/6/68/Hang-Things-on-a-Cement-Wall-Step-6.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-6.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/6/68/Hang-Things-on-a-Cement-Wall- Step-6.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-6.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Wait 30 to 60 minutes for the glue to dry. After the glue dries, you can hang the item on the hook.

If the item causes the wall hook to come off even after you’ve waited for the glue to dry, double-check the specs to see if the hook you’re using can support the weight of the item to be hung.

Use a staple wall hook

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/2/23/Hang-Things-on-a-Cement-Wall-Step-7.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-7.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/2/23/Hang-Things-on-a-Cement-Wall- Step-7.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-7.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Buy a 25 pound (11 kg) pushpin wall hook. This type of hook is specifically designed for cement and brick walls. Each hook includes four extra-strong pins that secure it to the wall.

You need a hammer to make a staple hanger.
Use 2 hooks to hang the same object if necessary and remember to prepare support tools.

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/2/26/Hang-Things-on-a-Cement-Wall-Step-8.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-8.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/2/26/Hang-Things-on-a-Cement-Wall- Step-8.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-8.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Mark the point where you want to attach the hanger to the wall. If the item has a steel wire in the back, pay attention to the slack when choosing a hanging position. Test by stretching the center point of the rope towards the top of the object. Measure the distance from the bottom of the item to where the center of the wire reaches when fully stretched.

If you are using 2 staples, measure the distance between the two built-in hooks on the back of the item or the width of the item and divide by 3. Either of these results helps you determine the distance between the two points of need. marked on the wall.

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/7/7b/Hang-Things-on-a-Cement-Wall-Step-9.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-9.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/7/7b/Hang-Things-on-a-Cement-Wall- Step-9.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-9.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Use a hammer to hammer each small pin into the wall through the available holes. Press the hanger to the wall so that the center of the base coincides with the marked position. Use one hand to hold the hook and the other hand to hold the hammer to drive four pins into the wall one by one (drive the pins half deep). Release the hanger holder and see if the hook is in place. Finally, use a hammer to drive the nail deep into the wall.

To avoid hitting your finger with the hammer, you need to be very gentle during the first few beats. When you feel the pin is firmly attached to the wall, release the hand holding the hanger and hammer the tip of the nail to close it.

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/1/18/Hang-Things-on-a-Cement-Wall-Step-10.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-10.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/1/18/Hang-Things-on-a-Cement-Wall- Step-10.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-10.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Fasten the wire or rope of the item on the hook. Stand back to see if the object is skewed. Adjust further if needed and enjoy the results.

Install expansion screw

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/5/56/Hang-Things-on-a-Cement-Wall-Step-11.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-11.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/5/56/Hang-Things-on-a-Cement-Wall- Step-11.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-11.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Choose expansion screws to hang objects heavier than 25 pounds (11 kg). Expansion screws are usually made of plastic and are used to drive screws. You need the drill and the drill bit to be the same size as the hatch screw. ^{[3] X Research Sources}

You can purchase a mechanical kit that includes an expansion screw, a screw, and a properly sized drill bit. ^{[4] X Research Sources}
Hang an object with two expansion screws if necessary.

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/7/7f/Hang-Things-on-a-Cement-Wall-Step-12.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-12.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/7/7f/Hang-Things-on-a-Cement-Wall- Step-12.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-12.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Using a hammer drill is best. You can use a regular electric drill with a drill bit, but the drilling speed is relatively slow and can cause a hole in the wall much larger than expected. Buy or borrow a hammer drill if possible. ^{[5] X Research Sources}

You can rent a hammer drill at a hardware retailer near your home, a home repair supply chain system Lowe’s, a Home Depot building materials store or a rental repair shop. Remember to call before coming.

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/b/bd/Hang-Things-on-a-Cement-Wall-Step-13.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-13.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/b/bd/Hang-Things-on-a-Cement-Wall- Step-13.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-13.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Drill screw holes. Measure carefully and mark the screw position. Place the drill bit on the position to be drilled. Be sure to hold the machine firmly and check that your drill bit, handle and arm are parallel to the floor. Drill with firm pressure against the wall and stand firmly.

For cement walls, it is best to drill at the slowest speed. ^{[6] X Research Sources}

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/d/df/Hang-Things-on-a-Cement-Wall-Step-14.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-14.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/d/df/Hang-Things-on-a-Cement-Wall- Step-14.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-14.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Insert the expansion screw into the hole and use the hammer to cover the expansion. The expansion screw should fit snugly into the drilled hole but should not be too tight to avoid heavy hammering. If the hole is too small, replace the drill with a larger diameter and drill again.

{“smallUrl”:”https://www.wikihow.com/images_en/thumb/4/4f/Hang-Things-on-a-Cement-Wall-Step-15.jpg/v4-728px-Hang-Things- on-a-Cement-Wall-Step-15.jpg”,”bigUrl”:”https://www.wikihow.com/images/thumb/4/4f/Hang-Things-on-a-Cement-Wall- Step-15.jpg/v4-728px-Hang-Things-on-a-Cement-Wall-Step-15.jpg”,”smallWidth”:460,”smallHeight”:345,”bigWidth”:728,”bigHeight” :546,”licensing”:”<div class=”mw-parser-output”></div>”}

Insert the screw into the hatch. Use a screwdriver or screwdriver in the drill set to tighten the screws. Stop before the screw goes deep into the wall because you need to hook a wire or hang something on the part of the screw body that sticks out. Hang items, align them for balance and enjoy the fruits of your own labor.

Warning

Be sure to read and follow the instructions for operating the drill carefully before using it.
Protect your eyes while drilling. Consider wearing sunglasses or goggles.
Use a wall detector with metal detection to make sure you’re not drilling into an underground power line by mistake.

Things you need

When attaching the wall hook

Optional wall hook
Alcohol cleaning solution
Clean rag or tissue
Pencil
Roll Ruler

When using a pushpin wall hook

Staple wall hook
Hammer
Pencil
Roll Ruler

When installing the expansion screw

Expansion screws and screws
The drill bit is the same size as the expansion screw
Hammer drill or conventional electric drill
Pencil
Roll Ruler

Steps